Tube inspection and release record
Tube Cut Part Inspection Record
Record tube OD/profile dimensions, wall, length, feature results, orientation, end features, interior condition, seam, and cut edge against the user’s drawing or documented job requirements. No default tolerance or sampling plan is assumed.
Content reviewed 2026-11-02. Verify the applicability of each source before using a value in a quote.
Input to record
Drawing revision, material/batch, profile orientation, explicit limits, actual sample measurements, qualitative evidence, sampling plan, and authorized reviewer.
Output to carry forward
A review status and CSV record. Release is available only as the named shop reviewer’s recorded decision after applicable measurements/evidence are complete.
Tube inspection record
Enter actual measurements and the drawing’s explicit limits, then document the observed profile, orientation, end features, interior, seam, and edge condition. No tolerance or sampling plan is preselected. Inputs remain local and clear on reload.
Observed conditions
HOLD
11 incomplete or outside-requirement checks. Job, sampling, method, criteria, or reviewer fields are incomplete.
A release request stays HOLD until every applicable check and evidence field is resolved and at least one actual measurement is recorded. This is the user’s inspection record; the tool does not inspect a physical part, verify documents, or infer acceptance of unmeasured parts.
Inspection scope
Name the sample or part IDs, measurement methods, and drawing revision. Compare each numeric result to the explicit requirement supplied by the user; do not substitute a site-wide tolerance. For seam, orientation, interior, edge, burr, and distortion checks, retain the observed evidence and the requirement source.
A release record applies to the inspected sample and stated plan. It does not infer acceptance for unmeasured parts or certify machine capability. Keep failed and held results with the job packet and route unresolved conditions to the responsible quality/process owner.
Sources and scope
Content reviewed 2026-11-02. A documentation reference supports the stated method or data only; it does not approve settings on another machine.
- BLM GROUP LT7 overview
Lists round, square, rectangular, open, and special profiles for a configured LT7. This is product information, not an operating/fixture manual or a universal profile approval.
- BLM GROUP LT7 technical information
Describes machine-specific supports and handling features. It does not provide the fixture clearances, clamping torque, rotation settings, feature minima, inspection tolerances, or approval procedures needed for your machine.
- LaserCalc Pro authored review method
The rotation equations and drawing-owned review ledgers are deterministic worksheets authored for this site. They preserve user-supplied drawing, CAM, fixture and measured evidence; they are not OEM limits, safety clearance, or manufacturing certification.
Showing 7 of 7 rows
| Inspection item | Requirement | Actual / evidence | Disposition rule | Source / method | Applicability | Confidence | Reviewed |
|---|---|---|---|---|---|---|---|
| OD / width / height / wall / length | Enter the drawing limits and units for each applicable measured dimension | Record actual value, sample/part ID, gage/method, and evidence | Within/outside recorded numeric limits; a blank limit or evidence remains HOLD | User drawing and actual inspection record; comparison arithmetic by LaserCalc Pro | Only the stated feature, sample, drawing revision, and measurement method | No default tolerance or sampling plan | 2026-11-02 |
| Profile identity / form | Drawing profile, material, orientation datum, and required form condition | Record observed condition, sample identity, method, and evidence against that requirement | User records meets / does not meet / N/A with reason; unresolved checks remain HOLD | User drawing or documented job requirement; LaserCalc Pro inspection ledger | Recorded sample/part and requirement only; not a batch inference | Manual observation; no automatic quality certification | 2026-11-02 |
| Feature orientation | Drawing face/datum and angular or relational requirement | Record observed condition, sample identity, method, and evidence against that requirement | User records meets / does not meet / N/A with reason; unresolved checks remain HOLD | User drawing or documented job requirement; LaserCalc Pro inspection ledger | Recorded sample/part and requirement only; not a batch inference | Manual observation; no automatic quality certification | 2026-11-02 |
| End-feature pattern | Required holes, slots, notches, bevels, and intended wall(s) | Record observed condition, sample identity, method, and evidence against that requirement | User records meets / does not meet / N/A with reason; unresolved checks remain HOLD | User drawing or documented job requirement; LaserCalc Pro inspection ledger | Recorded sample/part and requirement only; not a batch inference | Manual observation; no automatic quality certification | 2026-11-02 |
| Interior / opposite wall | Documented interior condition and inspection access/method | Record observed condition, sample identity, method, and evidence against that requirement | User records meets / does not meet / N/A with reason; unresolved checks remain HOLD | User drawing or documented job requirement; LaserCalc Pro inspection ledger | Recorded sample/part and requirement only; not a batch inference | Manual observation; no automatic quality certification | 2026-11-02 |
| Seam / surface condition | Drawing or documented job requirement for seam orientation and surface condition | Record observed condition, sample identity, method, and evidence against that requirement | User records meets / does not meet / N/A with reason; unresolved checks remain HOLD | User drawing or documented job requirement; LaserCalc Pro inspection ledger | Recorded sample/part and requirement only; not a batch inference | Manual observation; no automatic quality certification | 2026-11-02 |
| Cut edge / burr / distortion | Documented edge, finish, and distortion requirement; no default tolerance | Record observed condition, sample identity, method, and evidence against that requirement | User records meets / does not meet / N/A with reason; unresolved checks remain HOLD | User drawing or documented job requirement; LaserCalc Pro inspection ledger | Recorded sample/part and requirement only; not a batch inference | Manual observation; no automatic quality certification | 2026-11-02 |
Reference workflow
- Match the job, material, machine head, and quality requirement to a row.
- Confirm the source, review date, and confidence before copying the value into a quote worksheet.
- Use a measured result or current OEM record when the row is marked as required or unverified.